Navigation

Top News

Statistics

Advertisement

How to remove the front and rear bumper Cadillac Escalade GMT900 (2007-2013)


Depending on the body type, the attachment points may differ.
Below are the wiring diagrams for the bumpers. The arrows indicate the location of the screws and caps.
  • LIKE
  • 2
Author: carsoftos777 | 22-02-2023, 03:23 | How To Remove Bumpers | Views: 507 | Comments: 0


- remove the grille
- unscrew the self-tapping screw under the grate
-along the edges of the front part of the bumper, remove the decorative grilles (if any) and Unscrew the two hex bolts, they are twisted from the bottom up.
-pull off the edges of the bumper from the side locks (pull the edge of the bumper down and towards you).
  • LIKE
  • 2
How to remove front and rear bumper Peugeot 807 (Fiat Ulysse 2, Lancia Phedra, Citroën C8)


-open the hood.
-under the hood take out the caps that secure the top.
- around the perimeter of the lower part, unscrew the fasteners (you need to turn a quarter of a turn).
-in the wheel arches, Unscrew the screws and take out the caps, release the fender liner.
-for the fender liner, Unscrew the screws that attach the corners to the wings.
  • LIKE
  • 2
Author: carsoftos777 | 20-02-2023, 03:49 | How To Remove Bumpers | Views: 485 | Comments: 0
How to remove front and rear bumper BMW 3-series E90


-along the entire length of the lower part of the bumper, Unscrew the seven screws (spun up).
-Unscrew the wheels left or right, depending on which side you will unscrew first, and in the wheel arches, Unscrew the screws that attach the fender liner to the bumper.
-move the edges of the fender liner to the side and Unscrew two bolts on each side that secure the bumper to the wings (spun up).
-under the hood, Unscrew the four bolts that secure the upper part of the bumper.
-pulls the bumper over.
  • LIKE
  • 2
Author: carsoftos777 | 20-02-2023, 03:02 | How To Remove Bumpers | Views: 447 | Comments: 0
How to remove the front and rear bumper AUDI A3 II


-under the hood, Unscrew the three bolts that secure the grille and bumper to the top bar (the bumper is removed with the bumper).
-along the entire length at the bottom of the bumper, unscrew the screws securing the engine protection to the bumper (it is not necessary to remove the protection).
-Unscrew the wheels left or right, depending on which side of the bumper will be unscrewed first.
-Unscrew three screws on each side (usually poses an asterisk) that attach the fender liner to the bumper.
  • LIKE
  • 2


-open the hood.
-remove the grille.
-Unscrew one screw (spun down) between the headlights.
-from the bottom, Unscrew the screws that secure the protection.
-depending on which side we will disassemble, turn the wheels.
-in the wheel wells, Unscrew the screws that secure the fender liner (front).
  • LIKE
  • 3
Author: carsoftos777 | 18-02-2023, 02:37 | How To Remove Bumpers | Views: 1 836 | Comments: 0
How to remove the front and rear bumper AUDI A6 C7


The bumper is removed along with the grille.
Depending on the year of manufacture and type of model, the attachment points differ slightly.
  • LIKE
  • 2
How to remove the front and rear bumper of a Chevrolet Epica (after 2006)



-open the hood.
-under the hood take out the caps and remove the trim.
-under the trim, Unscrew the two screws that secure the top.
-Unscrew three screws on each side (spun down) and pull out the headlights.
-in the openings of the headlights, Unscrew one screw and take out two caps on each side.
  • LIKE
  • 2


The bumper is removed along with the amplifier.
-open the hood.
-under the hood, Unscrew the screws, release the latches and remove the grille.
  • LIKE
  • 2
Author: carsoftos777 | 13-02-2023, 03:59 | How To Remove Bumpers | Views: 1 132 | Comments: 0
How to remove the front and rear bumper AUDI A1


-Unscrew the screws around the perimeter at the bottom (spun up).
-turn the wheels to the side, depending on which side you will disassemble first.
-in the wheel arches, Unscrew the screws that secure the fender liner.
-move the fender liner to the side and take out one piston (inserted from the bottom up) that attach the bumper to the wings.
-under the hood, Unscrew the three screws that
  • LIKE
  • 2